Case Study

Balfour Beatty

Reducing underground service strikes through digital Control of Works

97,810
Digital safety permits issued in 2025
34%
Fewer UK underground service strikes
128 → 84
UK service strikes, 2024 to 2025
    Categories
    Construction

    Reducing underground service strikes through digital Control of Works

    2025 safety performance data review

    Underground service strikes remain one of the most persistent high-potential risks in construction and infrastructure delivery.

    Despite established permit-to-work processes, utility records, CAT & Genny surveys and excavation procedures, strikes continue to occur across the industry. The challenge is rarely a lack of documentation. More often, it is a failure to consistently apply the right controls at the point of work.

    In 2022, Balfour Beatty appointed SiteAssist as its digital permit partner, and mandated the use of digital permits from January 2024.

    In 2025, Balfour Beatty issued more than 97,800 digital safety permits across its business.

    Balfour Beatty's Annual Report 2025 highlights improved safety performance, with UK underground service strikes reducing from 128 incidents in 2024 to 84 in 2025 - a decrease of 34%.

    Source: Balfour Beatty plc Annual Report & Accounts 2025. The reduction is attributed to digital permits alongside a reinforced utilities avoidance procedure; SiteAssist is a named platform partner in the report.

    Understanding the risk

    Underground service strikes sit within a category of events that are both relatively common and potentially catastrophic.

    A strike involving a low-voltage cable may result in localised disruption and repair costs. A strike involving a high-voltage asset, gas main or critical utility can result in serious injury, fatality, major programme disruption and regulatory investigation. The top of the sentencing range for a large organisation's most serious health and safety offence is £10M+.

    The challenge for contractors is that excavation work often appears routine. The majority of excavations are completed without incident, which can create confidence in processes that have never been tested by failure. As a result, organisations can become focused on permit compliance rather than the effectiveness of the controls the permit is intended to enforce.

    The objective from SiteAssist was not simply to replace paper forms with digital versions, but to improve control across the entire excavation process by:

    • Standardising permit workflows
    • Connecting permits to site-specific hazards
    • Improving visibility of excavation activities
    • Introducing stronger control points before work begins
    • Creating a consistent audit trail across projects
    • Generating data that could be used to improve future performance
    Why traditional permitting has limitations

    Most permit systems are designed to demonstrate authorisation. They provide evidence that work has been reviewed, approved and communicated. They create an audit trail and establish accountability.

    However, permits alone do not verify that:

    • The latest utility information has been reviewed.
    • Appropriate detection methods have been completed.
    • Site conditions remain consistent with the original assessment.
    • Hold points have been completed before excavation begins.
    • Lessons from previous incidents are being incorporated into future work.

    In practice, these controls often sit across multiple systems, documents and teams.

    A Control of Works approach

    The most effective excavation safety programmes treat the permit as one component of a wider control framework. That framework typically consists of four connected stages:

    • Asset understanding. Utility records, surveys and site intelligence are reviewed to establish what assets may be present and where uncertainty exists.
    • Hazard identification. Known and potential underground hazards are identified, assessed and linked directly to the planned activity.
    • Control implementation. Permits, hold points, briefings and verification activities are used to ensure controls are applied before excavation proceeds.
    • Feedback and learning. Observations, near misses, inspections and incidents are captured and used to improve future planning and execution.

    When these activities operate as a connected process, organisations move beyond permit administration towards active control of excavation risk.

    What the results indicate

    Balfour Beatty's reported reduction in service strikes should not be interpreted as the result of digitisation alone.

    A key takeaway is the combination of digital permitting with strengthened utilities avoidance procedures.

    Digital systems are most effective when they improve the consistency, visibility and enforcement of operational controls.

    By connecting permit workflows to risk information, site verification activities and auditable hold points, organisations are better able to ensure that critical controls are applied before work starts rather than reviewed after an event.

    This can support improved control over one of the industry's most significant fatal and major injury risks.

    In an environment where a single utility strike can have significant operational and financial consequences, the ability to systematically manage excavation risk becomes a critical business capability.

    Balfour Beatty's 2025 results provide a practical example of what can be achieved when digital permitting forms part of a broader Control of Works strategy rather than functioning as a standalone compliance process.

    |inject-quotes|

    Lee Hewitt, Group Business Services Director, Balfour Beatty

    Beyond compliance

    For major contractors and infrastructure operators, the value of reducing service strikes extends beyond incident statistics. Each avoided strike represents reduced exposure to:

    • Injury and fatality risk
    • Corporate and individual liability
    • Regulatory investigation
    • Asset damage and repair costs
    • Programme disruption
    • Client and stakeholder impact
    An app digitises a form. A platform controls the work.

    An app on its own digitises a single document, records that a step was done, lives in isolation from the site and leaves the judgement to the user.

    A Control of Works platform:

    • Controls the whole excavation chain
    • Enforces the right control at the right moment
    • Connects map, hazard, permit and data
    • Makes the next dig safer than the last

    Control the work. Not just the paperwork.

    quote
    SiteAssist plays an important part in how we set people to work, and in the reduction in service strikes we have seen over recent years. Alongside our utilities avoidance procedures, it makes sure the right process is followed every time.
    Dark gray close or cancel icon with an X shape centered inside a square with rounded corners.
    Request a demo
    Find out how we can help
    you achieve your goals.
    Thank you! Your request has been received!
    Oops! Something went wrong while submitting the form.